Standard is used most for model making and sculpting but Superfine White is the better choice if you’re looking to make something very detailed. There are five different types of Milliput – Standard, Silver Grey, Superfine White, Black and Terracotta. Once the Milliput wash has dried, you can sand it to make it super smooth or add colour to it with acrylic paint. The top layer of Milliput will dissolve in the water and create an adhesive ‘wash’ which you can use to fill in gaps with a paintbrush. Take a small amount of Milliput, make a hole in the middle with the end of your paint brush and put a drop of water in it. The best way to do this is to mix Milliput with a small amount of water as it’s easier to shape and smooth once it’s wet. Milliput is also used to fix gaps and joins in models, such as mould lines (small seams often found in miniatures). It can also be used as a modelling clay itself for making things like dollhouse food, miniature stones or bricks, sandbags in war gaming dioramas or any small models! When I used it, it was to cover the wire armature of a miniature tree.Īs the material sets so hard, it’s particularly good for creating things like realistic looking bricks, walls and stones. Milliput is predominantly used for filling gaps to help create a smooth surface on miniature models – it works particularly well for disguising seams in plastic models. What is Milliput used for in making miniature models? Milliput sounds like the dream material so I wanted to look into it a little more to find out how it can be used in making miniature models. It’s also waterproof and can even set hard underwater. It sets extremely hard and once cured, you can sand, drill or paint it. The putty can be used in a huge range of applications, from fixing leaky pipes, to repairing ceramics, to making miniature models. Milliput is an epoxy putty which comes in two sticks – when you mix the sticks together it becomes a soft putty that will harden like stone in about 2 to 4 hours. I’d never heard of it, but he very kindly shared his knowledge with me – as a veteran model boat, aeroplane and railway enthusiast, he’s used Milliput for many years. We recommend putting film of Paraloid B-72 on the surfaces that will adhere to the Milliput, which can then be loosened again with acetone.Ĭan also be used for mould making and can be cast.My father-in-law Neil introduced me to Milliput when I was looking for something to use to make the bark on a wire armature for a mini tree. Whilst Milliput is permanent and highly adhesive, it is possible to remove. Kept separately, these two parts will last a long time unused. Like epoxy glue, there are two sticks in a pack - one resin and one hardener. When performing fossil restoration, the texture achieved is vital and colour is better matched afterwards with acrylic paints. Strong powder pigment rather than powder paint is better as smaller amounts can be used. You can blend different Milliput colours together to aid with colour matching, but it is not recommended to mix with matrix as it will change the properties of the resin. Powder pigment can be mixed in, in small quantities, so that the mixture does not become too dry and crumbly. Milliput goes rock hard in two to three hours at normal room temperature (faster with heat, and can be kept as putty for 72 hours in the freezer). ![]() ![]() It can then be manipulated like modelling clay. Milliput is used by blending equal amounts of each stick (two in a pack), by rolling and kneading until the colour is uniform and free from streaks. the ZOIC MR Microraptor or VR Velociraptor). If the surface has already set and needs further adjusting, this can be done with a gentle air pen (e.g. Modelling using clay modelling tools whilst the putty is still clay-like is recommended, and adding a drop of water to the surface and rubbing it in will remove fingerprints and smooth the surface. Colour can be achieved by blending different types of Milliput together, or by painting with quality acrylics. ![]() It can be used as a gap or crack filler, or sculpted into whatever shape is required. When it is set, it can then be sandpapered, painted and varnish. It is used widely for restoration and repair of fossils, as it doesn't shrink, bubble crack or change shape over time. Milliput ® is a two-part epoxy putty that adheres exceptionally well to rocks and fossils.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |